HELP with headunit and bose system!!

[adge_dre]

ok got everything i need

metra 1784 VW
pac soem4
aftermarket headunit

i connected them using tape before i solder to get a better understanding but the wires arnt actually connected yet. Can someone tell me if this is correct here is the link to where i got the info.


http://www.club202.com/forums/showthread.php?16435-What-do-I-need-for-aftermarket-HU&highlight=bose+system

i connected the wires referencing 97c280. i put the aftermarket headunit on the input side of the pac and the metra on the outside. again wasnt sure about if this was correct.

"Ok, I think I've got a solution but not entirely sure (it makes sense in my head)"

METRA HARNESS>AFTERMARKET HU HARNESS
red>yellow
yellow>red
black>black
orange/white>orange/white
blue/white>blue/white

METRA HARNESS>PAC LOC
white>white
white/black>white/black
green>green
green/black>green/black
grey>grey
grey/black>grey/black
purple>purple
purple/black>purple/black

AFTERMARKET HU>PAC LOC
white>white
white/black>white/black
green>green
green/black>green/black
grey>grey
grey/black>grey/black
purple>purple
purple/black>purple/black

***UNUSED WIRES***
PAC LOC: BLUE, YELLOW, BLACK(x3)
AFTERMARKET HU HARNESS: Light Blue, Blue2490

[Denlasoul]

That sounds about right, but would need to pull out my system to confirm. I used a wiring diagram that was posted somewhere on the site.

edit: I tried searching for the wiring diagram. Unfortunately, when we changed over servers alot of the pictures and proper links were scrambled. IIRC, I have a hard copy of the diagram at home. If you can hold out a day or so, I can look for it and post up a copy.

Den

[adge_dre]

That sounds about right, but would need to pull out my system to confirm. I used a wiring diagram that was posted somewhere on the site.

edit: I tried searching for the wiring diagram. Unfortunately, when we changed over servers alot of the pictures and proper links were scrambled. IIRC, I have a hard copy of the diagram at home. If you can hold out a day or so, I can look for it and post up a copy.

Den

that would be great, can you post asap. thankyou. i was going to try and install today but since you said you can confirm ill wait

[jnolte]

hopefully you can find the constant power cause its switched and i can't remember which wires, its been so long. sorry I'm not much help just a heads up from what i remember when i installed my head unit 9years ago

[jnolte]

found a helpful post http://www.club202.com/forums/showthread.php?713-alipne-cd-player-95-c36&highlight=headunit+wire

[adge_dre]

found a helpful post http://www.club202.com/forums/showthread.php?713-alipne-cd-player-95-c36&highlight=headunit+wire

The hardest thing is wiring the PAC which I still have not got yet:

[adge_dre]

Did you ever find that wiring diagram?

[Denlasoul]

No I did not. I will have to pull out my hu to get the wiring schematics.

[adge_dre]

Its ok. I finally got it after four hours of playing around with the wiring. Couldn't figure it out. Turns out it was just the blue wire that wasn't connected on the PAC to the wiring harness. Thanks anyway!

[Logic]

Its ok. I finally got it after four hours of playing around with the wiring. Couldn't figure it out. Turns out it was just the blue wire that wasn't connected on the PAC to the wiring harness. Thanks anyway!
did you try installing the radio without the pac piece ? if so did the volume get loud quick and was there popping when it was turned on or pressing of buttons ? in some cases the soem4 piece is to allow adjustment if the radio gets loud to fast or popping noises if they are there . if not the pac piece is not needed in some cases , i also seem some harnesses that have the RCA ends on instead of wiring which allow low level into the harness instead of high level .