BolivianFuego
08-16-2015, 01:16 PM
Hey guys,
So I had made a post here earlier on where to get cheap brake pads and rotors. I ended up getting OEM all around.
I had my brake pad sensor go off so that's when I finally got on it. I decided to start with the driver's side front.
What a pain in the ass i is to work on Benz's!!! I didn' have the t45 Torx bit and had to go buy it and ended up just geting a whole new torx set. Well, after pulling the driver's side calipher, I noticed the pad was actually still pretty meaty....which was strange. Worn yes--but still plenty left. I put it back together, not to mention that damn anti-rattle thing...what another PITA!
I did the pass side, and noticed instantly that the pad was A LOT lower than the driver's side. What could that mean? It either meant the last owner got hosed or something is wrong with the calipher..... I also had issues with the piston being 'sticky' and harder to push in than the driver's side which was easily done with a screw driver.
I used a C clamp to push in the pass side piston and it was REALLY hard. With that and the signifigant difference in wear, this means the calipher is basically toast, right?
I ended up working on the rear driver's side and noticed the same thing about like the driver's front side. Pads still had plenty of meat left on them. I only encountered one issue, and that was the rotor WOULD NOT come out in the back. calipher was cake. Came out easy and the screw that held in the rotor was easy too. Same with pads--no issue. Why was the rotor stuck?
I have the old pads and rotors in the back still in. I said screw it, because I am just going to have someone else install most likely a new pass calipher and while they do that, have them do the pads and rotors in the rear.....unless you guys know the trick on how to take the rotors out in the back?
I read that in these cars (I have a 1999 C280 by the way), the rotor can get stuck because of how the brakes in the back work. What did I do wrong? And is the calipher screwed in the front? Or can a pro fix it?
Edit: And I should basically lay off driving it until I get it fixed, right? To not have uneven wear of the pads/rotors in the front?
So I had made a post here earlier on where to get cheap brake pads and rotors. I ended up getting OEM all around.
I had my brake pad sensor go off so that's when I finally got on it. I decided to start with the driver's side front.
What a pain in the ass i is to work on Benz's!!! I didn' have the t45 Torx bit and had to go buy it and ended up just geting a whole new torx set. Well, after pulling the driver's side calipher, I noticed the pad was actually still pretty meaty....which was strange. Worn yes--but still plenty left. I put it back together, not to mention that damn anti-rattle thing...what another PITA!
I did the pass side, and noticed instantly that the pad was A LOT lower than the driver's side. What could that mean? It either meant the last owner got hosed or something is wrong with the calipher..... I also had issues with the piston being 'sticky' and harder to push in than the driver's side which was easily done with a screw driver.
I used a C clamp to push in the pass side piston and it was REALLY hard. With that and the signifigant difference in wear, this means the calipher is basically toast, right?
I ended up working on the rear driver's side and noticed the same thing about like the driver's front side. Pads still had plenty of meat left on them. I only encountered one issue, and that was the rotor WOULD NOT come out in the back. calipher was cake. Came out easy and the screw that held in the rotor was easy too. Same with pads--no issue. Why was the rotor stuck?
I have the old pads and rotors in the back still in. I said screw it, because I am just going to have someone else install most likely a new pass calipher and while they do that, have them do the pads and rotors in the rear.....unless you guys know the trick on how to take the rotors out in the back?
I read that in these cars (I have a 1999 C280 by the way), the rotor can get stuck because of how the brakes in the back work. What did I do wrong? And is the calipher screwed in the front? Or can a pro fix it?
Edit: And I should basically lay off driving it until I get it fixed, right? To not have uneven wear of the pads/rotors in the front?